iipp publishingJournal of Applied Engineering Science

CHARACTERISTIC MICROSTRUCTURE OF MICRO HOT ROLLED PLATE STEEL VARIATING THE RADIUS OF BENDING TREATMENT WITH QUENCHING AND TEMPERING HEAT TREATMENT


DOI: 10.5937/jaes16-18078
This is an open access article distributed under the CC BY-NC-ND 4.0 terms and conditions. 
Creative Commons License

Volume 16 article 553 pages: 464- 470

Achmad Taufik* 
Department of Mechanical Engineering Faculty of Engineering, Brawijaya University, Malang, Indonesia
Department of Mechanical Engineering FTI National Institute of Technology, Malang, Indonesia

Agus Suprapto 
Department of Mechanical Engineering FTI National Institute of Technology, Malang, Indonesia

Ahmad As'ad Sonief
Department of Mechanical Engineering Faculty of Engineering, Brawijaya University, Malang, Indonesia

HRP Steel is heat treatable material that is manufactured by Krakatu Company Steel Indonesian, which the specification of HRP steel is classified as an armor 2nd class.To get the hardness and high strength, it is quenched (by heating it up to austenite temperature and held for a few moments, then cooled with water at T°C).Then the HRP Steel is heat treated again tempering (by heating it up to a certain temperature below the eutectoid line and retained for a while, then cooled with atmospheric air media) to improve its ductility. The purpose of this heat treatment is to improve the micro-structure that can affect the value of hardness. There are two additional (?) methods used in this research for treatment of that material: mechanical bending treatment with radius 55 mm and 60 mm. Analysis of the results of research shows that bending treatment and heat treatment modifies the morphology of micro-structure. In the 55 mm bending radius treatment and quenching-tempering treatment, a micro-structure formed of martensite structure that has higher percentage and has the form of a smooth martensite structure so that the value of Vickers hardness number is higher than the other treatment of 453 VHN treatment.

View article

The author would like to thank for their financial support of this work:
Directorate of Research and Community Service. Directorate General of Research and Development Reinforcement, Ministry of Research, Technology and Higher Ed-ucation, in accordance with Research Contract No. SP DIPA: 042.06.1.401516/2017, Date 07 December 2016. And  Prof.Dr.Ir.  Pratikto, MMT as Principal Counselor, Prof. Ir.Agus Suprapto, Meng., PhD , Co Promotor1 and Dr.Ir. Achmad As'ad Sonief, MT Co. Promotor2.
Results Discussions / Suggestions by:  Prof.Ir. Rochim Suratman, MEng., PhD (Technical Head of PT PINDAD)  Ir. Amung Sumantri, MM (Product Development Maneger of PT Krakatau Steel)

Cimpoeru, S. J. (2016) The Mechanical Metallurgy of Armours Steel. Defence Sains and Technology Group – Land Division. Australia.

G. Madhusudhan Reddy, T. Lee, G.R.N. Tagore, (1995) Weldability studies of high-strength low-alloy steel using austenitic fillers, Journal of Materials Processing Technology 49, 213 – 228

Su J. Et al, (2013) Simulation Analysis of Minimum Bending Radius for Lead Frame Copper Alloys, Journal of Material Science and Engineering 101-106, China

Krauss, R.M., & Hadar, U. (1999). The role of speech-related arm/hand gestures in word retrieval. In, R. Campbell & L. Messing (Eds.), Gesture, speech, and sign (93 – 116). Oxford: Oxford University Press.

Zuo X, Zhou Z. (2015) Study of Pipeline Steels with Acicular Ferrite Microstructure and Ferrite-bainite Dual-phase Microstructure. Materials research. 18(1):36-41.

Pereloma EV, Kostryzhev AG, AlShahrani A, Zhu C, Cairney JM, Killmore CR, et al. (2014) Effect of austenite deformation temperature on Nb clustering and precipitation in microalloyed steel. Scripta Materialia, 75:74-77.

Tian Y, Tang S, Wang BX, Wang ZD, Wang GD, (2012) Development and industrial application of ultra-fast cooling technology. Science China Technological Sciences, 55(6):1566-1571

Ravikumar SV, Jha JM, Mohapatra SS, Pal SK, Chakraborty S. (2013) Influence of Ultrafast Cooling on Microstructure and Mechanical Properties of Steel. Steel Research International. 84(11):1157-1170.

Wang G, Yan Y, Li J, Qiao L, Volinsky AA, (2013). Microstructure effect on hydrogen-induced cracking in TM210 maraging steel. Materials Science and Engineering, 586:142-148.

Briant, C.L.; Banerji, S.K, (1979) Tempered martensite embrittlement in phosphorus doped steels. Metall. Trans. A, (10), 1729–1737

Fang X, Fan Z, Ralph B, Evans P, Underhill R, (.2003) Effects of tempering temperature on tensile and hole expansion properties of a C–Mn steel. Material Processing Technology, (132) ;215–218.

Sharifi H, I Kheirollahi-Hosseinabadi, Ghasemi R., (2015) The Effect of Tempering Treatment on the Microstructure and Mechanical Properties of DIN 1.4021 Martensitic Stainless Steel. International Journal of ISSI , (12) 1; 9-15

Adamczyk J, Grajcar A, (2017) Heat treatment and mechanical properties of low-carbon steel with dual-phase microstructure. Journal of  achievements in Materials and Manufacturing Engineering, (22) 1;13-20

Daramola O. Oluyemi, Oladele Isiaka Oluwole, Adewuyi B. O, (2011) Studies of the Properties of Heat Treated Rolled Medium Carbon Stee. Materials Research. 14(2): 135-141

Handoyo, Yopi, (2015) Pengaruh Quenching dan Tempering Pada Baja JIS Grade 245C Terhadap Sifat Mekanis. Jurnal Ilmiah Teknik Mesin Universitas Islam Bekasi. Vol. 3, No. 2, Hal 102-115.