Istrazivanja i projektovanja za privreduJournal of Applied Engineering Science

RESEARCH OF DESIGN PARAMETERS INFLUENCE OF BUILDing WALL, CONSTRUCTED WITH THE HELP OF 3D PRINTER, ON ITS STRESS STATE


DOI: 10.5937/jaes0-28755 
This is an open access article distributed under the CC BY 4.0
Creative Commons License

Volume 18 article 728 pages: 565 - 570

Pakhomova Ekaterina Gennadievna*
Southwest State University, Faculty of Construction and Architecture, Department of Industrial and Civil Construction, Kursk, Russia

Monastyrev Pavel Vladislavovich
Tambov State Technical University, Institute of Architecture, Construction and Transport, Department of Urban Construction and Motorways, Tambov, Russia

Evdokimtsev Oleg Vladimirovich
Tambov State Technical University, Institute of Architecture, Construction and Transport, Department of Construction of buildings and structures, Tambov, Russia

Azawi Dubla Balthazar
Southwest State University, Faculty of Construction and Architecture, Kursk, Russia

The article presents the research results of design parameters influence of outer wall of a building erected in 3D technology, namely: wavelength of inner wall diaphragm, displacement of lower wave relative to upper wave of inner wall diaphragm (displacement of wave crest) on the stress state of a wall fragment subject to the constancy of its cross-section area. The set of data for analysis has been obtained on the basis of calculations in the SCAD ++ computer complex. The dependences of relative stresses of wall fragments on the studied factors have been obtained and the interpretation of research results has been given.

View article

1. Mishchenko, Ye.S., Monastyrev, P.V., Yevdokimtsev, O.V. (2018). Aspekty razrabotki obrazovatel'nykh programm v oblasti BIM-tekhnologiy s uchetom rabotodateley. Materialy 5-y mezhdunarodnoy nauchno-prakticheskoy konferentsii «Ustoychivoye razvitiye regiona: arkhitektura, stroitel'stvo, transport ». Tambov. TGTU, S. 385-392.

2. Dubrakova, K.O., Monastyrev, P.V., Klychnikov, R.Y., Yezerskiy, V.A. (2019). Optimization of thermal modernization of a group of buildings using simulation modeling. Journal of Applied Engineering Science, vol. 17, br. 2, str. 192-197, 2019, DOI: 10.5937/ jaes17-21683

3. Pakhomova, E.G., Jezersky, V.A. Monastyrev, P.V., Kuznetsova, N.V. (2020). The choice of aversion of the project proposal on restoration of the cultural heritage property on the basis of multicriteria comparative analysis. IOP Conference Series: Materials Science and Engineering, vol, 789(1), no. 012048, DOI: 10.1088/1757-899X/789/1/012048.

4. Monastyrev, P.V., Bal'tazar, A.D., Yevdokimtsev, O.V. (2019). Napryazhenno-deformirovannoye sostoyaniye elementov energoeffektivnykh sten, izgotovlennnykh po tekhnologii 3D-pechati. Sovremennaya Nauka: Teoriya, Metodologiya, Praktika. Sbornik nauchnykh stat'yey Materialy 1-oy Vserossiyskoy (natsional'noy) nauchno-prakticheskoy konferentsii, S.111– 116.

5. Monastyrev, P.V., Mishchenko, Ye.S., Azaui Dubla, B., Ovsyannikova, V.A. (2019). Ovsyannikov O.A. Analiz tekhnologiy vozvedeniya zdaniy s pomoshch'yu 3D-printerov. Zhilishchnoye stroitel'stvo, no. 9, 53-59.

6. Monastyrev, P.V., Yezerskiy, V.A., Ivanov, I.A., Bal'tazar, A.D. (2019). Analiz tekhnologiy 3D-pechati sten maloetazhnykh zdaniy i ikh klassifi katsiya. Sovremennyye problemy v stroitel'stve: postanovka zadach i puti ikh resheniya. Sbornik nauchnykh statey Mezhdunarodnoy nauchno-prakticheskoy konferentsii, S. 70-80.

7. Monastyrev, P.V., Yezerskiy, V.A., Ivanov, I.A., Azaui Dubla, B. (2018). Additivnyye tekhnologii vozvedeniya sten maloetazhnykh zdaniy i ikh klassifi katsiya. Fundamental'nyye, poiskovyye i prikladnyye issledovaniya RAASN po nauchnomu obespecheniyu razvitiya arkhitektury, gradostroitel'stva i stroitel'noy otrasli Rossiyskoy Federatsii v 2018 godu. Nauchnyye trudy RAASN. Tom 2, S. 368-379.

8. Monastyrev, Pavel V., Mishchenko, Elena S., Balthazar Azaoui Doubla, Ovsiannikova, Valeria A., Ovsiannikov, Oleg A. (2019). Analysis of technologies of buildings 3D printing and their classification. 21st General Assembly of the International Experts and Symposium Heritage as a Builder of Peace. Florence (Italy), Fondazione Romualdo Del Bianco Istituto Internazionale Life Beyond Tourism, P.363-369.

9. Pakhomova, E.G., Monastyrev, P.V., Mishchenko, E.S., Ezersky, V.A., Ivanov, I.A., Balthazar, A.D. (2019). House-building analysis when using additive technologies: classification, advantages and disadvantages. Journal of Applied Engineering Science, vol. 17, br. 4, str. 449-456, 2019, DOI: 10.5937/ jaes17-23635.

10. Apis Cor. We print buildings, from http://apis-cor. com/, accessed on 2020-08-20.

11. Monastyrev, P., Mischenko, E., Kuznetsova, N. Problems of Integration of Cultural Heritage Objects with Architectural and Historical Environment of the City. 2018 IOP Conf. Ser.: Mater. Sci. Eng., no. 463032045, DOI: 10.1088/1757-899X/463/3/032045.

12. Ezersky, V.A., Monastyrev, P.V., Ivanov, I.A. (2019). Theanalysis ofthermal properties of a wall fragment made with 3D construction technology. International Journal for Computational Civil and Structural Engineering, vol. 15, no. 4, 34-47.

13. Ledenev, V.V., Hoanganh, C.T., Monastyrev, P.V. (2017). Steel frame for the construction of exhibition pavilions. Izvestiya Vysshikh Uchebnykh Zavedenii, Seriya Teknologiya Tekstil'noi Promyshlennosti, no. 1, 280-284.

14. Mishchenko, Ye.S., Monastyrev, P.V., Yevdokimtsev, O.V., Strulev, S.A. (2019). Uchet pozitsii rabotodatelya pri proyektirovanii obrazovatel'nykh programm v oblasti BIM-tekhnologiy. Vestnik Povolzhskogo gosudarstvennogo tekhnologicheskogo universiteta. Seriya: Materialy. Konstruktsii. Tekhnologii. No. 2,. 106-115.

15. Mishchenko, E.S., Monastyrev, P.V., Evdokimtsev, O.V. (2018). Improving the Quality of Training in Building Information Modeling. ICL 2018, vol. 916, code 224239, 453-459.

16. Mishchenko, Ye.S., Monastyrev, P.V., Yevdokimtsev, O.V. (2019). Informatsionnoye modelirovaniye: obrazovatel'nyye programmy i professional'noye soobshchestvo. Sbornik materialov XX Mezhdunarodnoy nauchno-tekhnicheskoy konferentsii "Aktual'nyye problemy stroitel'stva, stroitel'noy industrii i arkhitektury", S. 204-209.

17. Company "Contour Crafting", from http://contourcrafting. com, accessed on 2020-08-20.